2008 Nissan Rogue Key Replacement

The 2008–2013 Rogue uses the same key setup, so everything on this page applies to those years too. The full picture is on the Nissan Rogue key guide.

2008 Nissan Rogue: key facts

Key type: Transponder chip key
Push-to-start: No
Transponder chip: ID46 (Philips Hitag-2)
Programming: OBD
All keys lost: We can originate new keys on site

Base trims: bladed ID46 key with keyed ignition. The optional Intelligent Key (CWTWBU729-style fob) pairs with a twist-knob ignition — a prox fob with no blade needed to start; pushToStart reflects the base setup.

What kind of key does a 2008 Nissan Rogue use?

On base trims, the 2008 Rogue uses a bladed key with a transponder chip inside the plastic head, paired with a regular keyed ignition. The chip family is ID46, also known as Philips Hitag-2, and that detail is verified in our reference data. It is not a push-to-start setup: you put the blade in the ignition and turn it.

What that means for you: the blade is only half the key. The car's immobilizer has to recognize the chip before the engine will run. A copy cut at a hardware store without a chip may turn the lock, but the Rogue will not start. The chip has to be programmed to the car, and on this model that is done through the OBD port.

These are the problems we see most often on this year of Rogue:

Worn ignition wafers and worn key blades on high-mileage cars, which make the key feel loose or hard to turn
Cracked key shells, broken remote buttons and dead remote batteries
Hardware-store copies cut without a transponder, which will not start the engine

Duplicate a key or start from all keys lost?

For this Rogue, making a duplicate is the simpler job, and it needs your original key to work from. If you still have one working key, replacing a spare now is usually the easier, lighter-cost route compared with waiting until the last key is gone.

If you have lost every key, that is still possible to solve. Our data shows an all-keys-lost job is doable on this setup. It just involves more steps because there is no working key to copy from. Programming is done by OBD, and it does not require NASTF SDRM access, so this is not a dealer-only situation for this key type.

Here is how a typical job goes:

You call (213) 577-1366 and tell us the year, model and whether you have any working key. We note the trim and ask about the key style.
We confirm the details by VIN or in person before cutting anything.
We cut the blade, and if the ignition is worn we check how the key turns before programming.
We program the ID46 chip and any remote functions to the car through the OBD port.
We test the key in the ignition, the door locks and the remote before you pay.

What affects the price of a 2008 Rogue key?

We don't quote numbers on a web page, because the real cost depends on a few things we can sort out in one phone call:

Whether you are duplicating from a working key or starting from all keys lost
Whether you want a plain transponder key or one with remote buttons
The condition of the ignition. A heavily worn ignition can complicate cutting and testing.
Whether you have the base keyed ignition or the optional Intelligent Key setup
Whether we come to you with a mobile van or you come to our storefront, which is usually the more economical route when your car can still be driven
How many keys you need made at the same visit

Locked out or need a locksmith now?

We answer around the clock, every day of the year.

Call (213) 577-1366

What we confirm by VIN before we start

Some 2008 Rogues were built with the optional Intelligent Key, a proximity fob that pairs with a twist-knob ignition, and that fob has no blade needed to start the car. Our data describes the fob as a CWTWBU729-style unit, but the key-facts table above reflects the base setup. The two systems are not interchangeable, so we confirm which one your car has by VIN or in person before we order or cut anything.

If you are not sure what you have, look at the ignition. A slot for a metal blade means the standard transponder key. A knob you twist means the Intelligent Key system. Either way, tell us on the phone and we will sort it out.

Wilshire Lock & Key has been in business since 1987, with a storefront at 10740 Wilshire Blvd in Westwood and mobile vans. You deal with one company, not a dispatch middleman, and David oversees the work. For more about this model across other years, see our Nissan Rogue key pages, the wider Nissan key replacement section, or our full car key service list. To book, use the contact page or call anytime.

Frequently asked questions

Can you make a 2008 Nissan Rogue key if I lost all of them?

Yes. An all-keys-lost job is possible on this Rogue. It takes more steps than copying a working key, but we program the new key through the OBD port, and it does not require NASTF SDRM access. Call (213) 577-1366 and we will confirm your setup by VIN.

Will a hardware-store copy start my 2008 Rogue?

Not if it was cut without a transponder chip. The blade may turn the ignition, but the engine will not start unless an ID46 chip is programmed to the car.

Do I need my original key to duplicate it?

For duplication, yes, the original key is needed to work from. If you don't have one, the job becomes an all-keys-lost job, which we can still handle.

Is the 2008 Rogue push-to-start?

The base setup is not. It uses a bladed key and a keyed ignition. An optional Intelligent Key with a twist-knob ignition exists, so we confirm by VIN or in person which one your car has.

My Rogue key is worn and sticks in the ignition. What should I do?

Worn blades and ignition wafers are common on high-mileage Rogues. Stop using the worn key if you can, and call us. We can cut a fresh key and check how the ignition responds before you end up stranded.

Can I just replace the remote battery or the cracked shell?

Often, yes. Dead batteries, cracked shells and broken remote buttons are common on this year. If the chip and the electronics still work, the repair can be simpler than a full replacement, and we can tell you after looking at the key.

Should a locksmith be licensed in California?

California requires locksmith companies to hold a BSIS LCO license. You should ask any locksmith for their license number before work begins.

We cover all these cities

Reviewed by David, Owner & Lead Technician, Wilshire Lock & Key — in the locksmith trade since 1987.

Last updated 2026-10-11.